How to Replace 1MZ-FE Engine on Toyota Avalon & Camry?

How to replace engine.Details to be followed to disassemble engine.
3.0L (1MZ-FE) and 3.3L (3MZ-FE) engine mounting accessories Diagrams and details.The complete step by step procedure is provided here:---

Go through the details and diagrams:----

Removal & Installation

1MZ-FE Engines

1. Before servicing the vehicle, refer to the Precautions Section.
2. Properly relieve the fuel system pressure.
3. Drain the cooling system.
4. Drain the engine oil.
5. Drain the transaxle fluid.
6. Remove or disconnect the following:
   
   
   Negative battery cable.

   Hood

   Battery and battery tray

   Accelerator and throttle cables

   Cruise control actuator, if equipped

   Air cleaner assembly, mass air flow meter and air cleaner hose

   Radiator

   Engine relay box

   2 igniter connectors

   Noise filter connector

   Connector from the left-hand fender apron

   2 ground straps and any other electrical connections keeping them from being removed

   Vacuum hoses from the engine.

   Fuel inlet and return hoses

   Heater hoses

   Transaxle control cable from the transaxle

   Instrument panel undercover, the lower instrument panel and glove box assembly

   3 ECM connectors, the 5 cowl wire connectors, and the cooling fan ECM connector. Push the engine wire through the cowl panel.

   Front exhaust pipe

   Halfshafts

   Power steering pressure tube

   Power steering pump

   A/C compressor without disconnecting the hoses

   Left-hand engine mounting insulator

   Right-hand engine mounting insulator

   Engine mounting shock absorber

   Front right engine mounting insulator
7. Attach a hoist chain to the engine hangers.
8. Remove or disconnect the following:
   
   NOTE

   Make certain all wires, connectors and hoses are cleared from the engine.
   
   
   
   
   Coolant reservoir hose and reservoir tank

   Right-side engine mounting stay bracket

   Engine control rod and bracket assembly
   
   
   
   
   Engine/transaxle assembly from the vehicle

To install:

1. Carefully lower the engine position. Keep the engine level while aligning the engine mounts.
2. Install or connect the following:
   
   
   Engine control rod and bracket. Tighten to 47 ft. lbs. (64 Nm).

   Right engine mount stay bracket. Tighten to 23 ft. lbs. (31 Nm).

   Engine ground straps.

   Coolant reservoir tank

   Front engine insulator. Tighten to 48 ft. lbs. (66 Nm).

   Engine mounting shock absorber. Tighten to 35 ft. lbs. (48 Nm).

   Left and right engine mounts. Tighten to 48 ft. lbs. (66 Nm).

   Power steering pump and A/C compressor

   Power steering pressure tube

   Halfshafts and front exhaust pipe

   Engine wires and connectors

   Transaxle control cable to the transaxle

   Fuel hoses and heater hoses

   All vacuum hoses, wiring and connectors

   Radiator

   Cruise control actuator

   Throttle cable and accelerator cable

   MAF meter, the air cleaner assembly, and air cleaner hose

   Hood

   Battery tray and battery

   Negative battery cable
3. Refill the cooling system to the correct level.
4. Refill the engine with oil to the correct level.
5. Fill the transmission with oil to the correct level.
6. Start the vehicle, check for leaks and repair if necessary.

Fig. 3.0L (1MZ-FE) and 3.3L (3MZ-FE) engine mounting accessories-2004

These details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html